EXHIBITION INFORMATION "MEX KANAZAWA 2025" MAY 15-17

We will be exhibiting at MEX Kanazawa, The MACHINERY&ELECTRONICS EXHIBITION in KANAZAWA to be held at Ishikawa Industrial Exhibition Hall.
The theme of Matsumoto Machinery this year is "Automation, Around the Clock.
We named it "Automation, Around the Clock" because it refers to a system in which robots take over the manufacturing process after workers leave the office on time and continue manufacturing around the clock.
(A detailed explanation of "utomation, Automation, Around the Clock" can be found in the middle of this page.)

At the booth, we will demonstrate the automation of the following processes using “Smart Terrace AIO,” a packaged robot system that automates setups.
Automation of (1) chuck jaw exchange, (2) workpiece measurement, (3) CAPTO tool exchange (4) lathe dog exchange will be demonstrated!
In addition to the automation lineup, machine tool peripherals that contribute to the best possible finish will also be on display.
The contents of our booth, which will provide solutions to the challenges of high-mix low-volume production, are a must-see for everyone involved in manufacturing!
We know you are busy, but please take this opportunity to stop by the Matsumoto Machinery booth.
We look forward to seeing you at our booth.

Outline of the event

Ishikawa Ironworking Machinery & Electrical Engineering Association
Dates】3 days from Thursday, May 15 to Saturday, May 17, 2025
Opening Hours】 10:00-17:00 *Close at 16:00 on the last day, Saturday, May 17.
Admission】Free
Venue】Ishikawa Industrial Exhibition Hall 1, 3, 4 >>Access
Booth No.] Hall 3, 105
Pre-registration for MEX Kanazawa is here.
MEX Kanazawa Pre-registration

Workshop Outline

We will hold a workshop again this year! We look forward to your participation.
[Date & Time]May 16, 2025 (Friday) 14:20-15:20
[Venue]Special workshop venue, Ishikawa Industrial Exhibition Hall No. 3
[Title]A peripheral device to support the introduction of robots
[Lecturer ]Naoki Okuno, General Manager, Development Department, Technology Division
Please register as soon as possible.
Workshop

Participation in Special Student Programs

We will introduce our company at the booth. There will be a special offer only for those who listen to the company introduction.
Please pre-register and visit our booth♪
Pre-register here
MEX KANAZAWA SPECIAL EVENT

"Automation, Around the Clock" solves the problems of high-mix low-volume production

High-mix low-volume production requires a lot of time for setup, and manpower shortage, machine utilization rate, and productivity have become issues.
Matsumoto Machine proposes robot automation as a means to solve such problems.
Automation of even a single lot is a matter of course. That is "Automation, Around the Clock".

Lineup of automated support that realizes Automation, Around the Clock

■Automatic set up exchange Robot System
Smart Terrace AIO-S ・Smart Terrace AIO-M

■Automatic jaw change chuck
HQJC ・AJC ・MAC

■Robot hand constant dimension device
■Out-of-machine workpiece measuring device
■CAPTO tool exchange
■lathe dog exchange device

Contributing to the best finish! Lineup to enhance on-site capabilities

■NC ROTARY TABLES FOR MC
・CX253R ・MD400L+AJC+AUTOMATIC CENTERING STOP DEVICE ・MDD230-ST230×2-01
　　

・MDATii800・MDDV200 ・FT1000-2
　　　

・FT153R-2

■ NC ROTARY TABLES FOR ELECTRICAL DISCHARGE MACHINING
・MTW86 (FOR WIRE EDM) ・MDHW100L (1-AXIS, FOR WATER-BASED EDM) ・SAT100 (2-AXIS, FOR BOTH WATER-BASED AND OIL-BASED EDM)
　　　　　　　　　　　　　　　　　